Changelog

Release:

1.9.5

Apr 24, 2021

Removed some 12v signals for Model 3 which were corrupted in later car firmwares

Removed 'Battery degradation' calculation, it showed too high degradation as it also counted 'initial settling' of the battery from factory


Release:

1.9.4

Dec 21, 2020

Fixed Android 10 storage permissions


Release:

1.9.3

December 13, 2020

What's new in this release?

AC/DC charge counters + Energy/Regen fix for Model 3 FW 2020.48.10


Release:

1.9.2

Jun 20, 2020

Started rollout at 20.00% across all countries.

What's new in this release?


Added FW2020.20.5 support for all cars (changes in capacity signal definitions and consequentially SOC calculation)


New signals for Model 3:

Usable remaining (nominal - buffer)

Full pack when new

Battery degradation (calc from fullpackwhennew)

Fixed series/parallell and temperature targets for later firmwares

DC-DC output parameters

Rated & Ideal range

Vehicle mass est

Trailer detected


New signals for Model S:

Temperature targets

Front drive temperatures

Removed motor Dissipation and motor input power as they are no longer on the CAN-bus


Release:

1.9.1

January 8, 2020

What's new in this release?

Model 3 new stuff:

- SOC Expected - subtracts cold battery and better matches the car screens. Thanks Blog!

More Model 3:

- Radiator fan target

- Radiator bypass

- Five way valve angle

- Front & rear motor oil temp & flow. Temps might be oil pump internal and not the fluid itself?

Thanks Michael Schwab!

- Tidying of Model 3 Perf tab

- Removed some HVAC signals that went crazy after recent firmware updates. Will return when we figure them out.


Release:

1.9.0

December 24, 2019

What's new in this release?

Teslalogger support (https://www.e-mobility-driving-solutions.com/ev-longterm-diagnostics-our-teslalogger/?lang=en)

Speed tab improvements

Fixed Model 3 temperature targets on 2019.40.2 firmware


Release:

1.8.6

November 30, 2019

What's new in this release?

ECO GRAND PRIX 24h EV race edition

HUD mode

Max Charge Power bugfix


Release:

1.8.5

November 17, 2019

What's new in this release?

Bugfixes:

- Arrows & copy button now disappears on delete

- Packets per second counter added 100 packets per second

New Model 3 signals:

- Max charge current (calculated from battery volts * max charge current)

- HVAC tab with signals contributed by Michael Schwab

- 12v battery status contributed by Michael Schwab


Release:

1.8.4

October 26, 2019

What's new in this release?

Added Model 3 signals:...

Max / min pack voltage

Max charge current

Max discharge current

Series/Parallel

Coolant active and passive target temps


Release:

1.8.3

What's new in this release?

Long-press auto selects item

Arrow buttons to move items

Copy-button

Bugfix on pasting duplicate items


Release:

1.8.2

What's new in this release?

Firmware V10 adjustments for Model 3:

New signals:

Front & rear Torque

Front & rear RPM

Front & rear drive unit temperatures

Steering angle

Pedal positions


Release:

1.8.1

What's new in this release?

Model 3 changes, to match firmware 2019.28.3.1 and later:

Removed F and R torque

Added old R torque (ID 0x108)

Changed F and R power definitions

Removed SOC UI, avg, min, max from Battery tab, to avoid confusion. Still exists in All tab.


Release:

1.8.0

August 5, 2019

What's new in this release?

Cell imbalance in mV for all cars

for Model 3:

Trips

Battery and powertrain coolant flow

Cell voltages: Min, max and mid

Totals tab, including:

AC charge total

DC charge total

Regen total

Energy (while driving) total

Regen %

Odometer distance

Consumption

Stationary (energy used while car is off)


Release:

1.7.4

July 3, 2019

What's new in this release?

Battery amp offset auto-detection, to support new firmware on 200 kw charge enabled cars

Added 'cell temp mid' for model 3


Release:

1.7.3

June 21, 2019

What's new in this release?

Re-introduced model S spam filter - should remove occational corrupt readings on slower adapters

Adjusted Model 3 speed scaling slightly

Fixed Model 3 speed wrap-around at 130 kph

BMS gauge now show units

Garbled gauges on tab change bugfix


Release:

1.7.2

June 2, 2019

What's new in this release?

Speed timers for Model S imperial units fix

If some timers (esp. 0-60) are not showing, select 'Factory reset this tab' for the Speed tab.


Release:

1.7.1

May 31, 2019

What's new in this release?

Speed timers fix with imperial units


Release:

1.7.0

May 26, 2019

What's new in this release?

New tab: Speed, with 0-60, 0-100 and other timers. The accuracy is not yet known, please compare to pro timing equipment and report back.

New gauge type: Model S BMS heatmap gauge can now be used in any tab

Moved the 'All' tab to the very end, to give users a lighter start, and remove some clutter

Model S changes:

  • 'Thermal load' -> 'Thermal controller'

  • 'Cooling/Heating' removed, replaced with 'Thermal Load'

Model 3 changes:

  • 'Battery temp' is renamed to 'battery min temp', as it gives the coldest cell/module


Release:

1.6.1

April 22, 2019

What's new in this release?

Model 3 improvements:

Layout, tab and signal refinements

Trip and Total tabs removed for now, as Trip system is not yet working for Model 3


Release:

1.6.0

April 7, 2019

What's new in this release?

Model 3 support!

Bugfixes

Model S/X thermal controller load

Numerous Android 9 compatibility and layout adjustments

We have some issues with Huawei P20 Pro, possibly some other Android 9 devices, where action is slow and stuttering. Please provide feedback if you manage to resolve this by phone power saving settings, or have other input regarding the issue.


Release:

1.5.1

October 25, 2018

What's new in this release?

  • Fixed 'coolant heater exit'

  • Fixed 'watt pedal'

  • Fixed Powertrain pump 2. Will only be visible if it gives > 0 %, to hide it on RWD cars which does not have it.

  • Added 'ATMA before filters', this will modify the behaviour of the bluetooth adapter setup and may improve compatibility with some ELM327 adapters


Release:

1.5.0

July 17, 2018

What's new in this release?

  • Factory reset this tab

  • Record button (long press for settings)

  • CAN dump (OBDLink MX hangs after a while, this is a MX firmware bug which they will not acknowledge)

  • Bluetooth/comms stability improvements

  • New BMS tab, idea by AndrĂ© Kjellstrup

  • Redesigned most tabs

  • Removed Cells tab

  • New readings:

  • Coolant heater

  • Series/Parallel

  • Battery pumps

  • Powertrain pump

  • Radiator bypass

  • Chiller bypass

  • Coolant heater

  • PTC air heater

  • Refrigerant temp


Release:

1.4.4

April 20, 2018

What's new in this release?

  • Gauges now scale better, and are more tablet friendly

  • SOC Min and SOC UI are back by popular demand and legacy reasons


Release:

1.4.3

March 25, 2018

What's new in this release?

  • Added 'Battery inlet' and 'PT Inlet'. These measure the coolant temperature going into the battery, and from crossover valve towards the drive unit(s). Battery Inlet measure the coolant after the battery heater

  • Redesigned Temps tab to include these

  • Improved error handling for bluetooth adapter

  • Fixed 4,999V on last cell of 75 batteries


Release:

1.4.2

Feb 24, 2018

What's new in this release?

  • 'BMS Max charge' & 'BMS Max discharge' are back, they were lost in the spam filter.

  • 'HVAC power' improved accuracy

  • Bluetooth handler stability and error catching improvements


Release:

1.4.1

Feb 15, 2018

What's new in this release?

- Reset Trip bugfix

- Status text overflow fix


Release:

1.4.0

Feb 8, 2018

What's new in this release?

- New tab: Efficiency and energy categorization

- Help menu

- New welcome screen

- Fixed unit conversion for HVAC

- Redesigned HVAC

- HVAC vent scaling fix (confirmed with Fluke)

- Some HVAC items removed, could not be confirmed. Others confirmed with Fluke and a hair dryer :)

- Total tab brought back. Note this tab can be inaccurate on older cars (regen shows too much and AC/DC charged too little)

- 'Combined power' bugfix (did not work alone)


Release:

1.3.0

Jan 1, 2018

What's new in this release?

- New BMS tab, resembles the car's BMS diagnostic screen

- Redesigned Temps tab

- 'Reset Gauge Throw' menu option

- Cell volt/temp gauge throw will reset every minute

- Removed wheel speeds from Perf tab (they only work on early Model S, but are still available for copying from the All tab)


Release:

1.2.0

Dec 9

What's new in this release?

- HVAC tab

HVAC controls decoded by Marc Olivier Chouinard from teslalog.com

Many items here are experimental, please test and give feedback if you find better naming or scaling of the values.

- Wheel speeds

- Calculated final drive gear ratios from RPM and wheel speeds (experimental)

- Improved brake pedal scaling

- New tabs can now be created from the tab menu

- Removed 3 old less accurate SOC calculations


Release:

1.1.0

Nov 3

What's new in this release?

"All" tab will now show the latest/newest items

Link to bluetooth settings from OBD selector

Timeout/retry of bluetooth connection

New SOC calculation: (nominalRemaining - buffer) / (nominalFullPackEnergy - buffer) * 100.0.

This seems to be exactly what the car shows you.

From the same logic:

- Usable full pack (nominalFullPackEnergy-buffer));

- Usable remaining (nominalRemaining-buffer));

These will hopefully be the most realistic estimates from this app so far.


Release: 1.0.0

Sep 25

What's new in this release?

Min/max values bugfix


Release: 0.9.9

Sep 24

What's new in this release?

Front RPM is back (taken by spam filter)

Gauges now work on Android versions older than 5.0

Unit conversion fixes (especially min/max values are now converted correctly)


Release: 0.9.8

Sep 13, 10:53 PM

What's new in this release?

Gauges! Work in progress, please report layout/size/font bugs or other strange behaviours

New default tabs and layouts! Reset tabs to see the new default layouts. (Stored trips will be lost)

lb/ft conversion fixed

More tidying of tabs

Added 'SOC nominal' calculated from Nominal remaining / Nominal Full Pack * 100


Release: 0.9.7

Aug 1, 8:14 PM

What's new in this release?

  • Trips

  • AC and DC charge counters

  • Stores your choice of metric/imperial units

Trips work with total counters from the car. This means that the start of a trip is merely a bookmark, you only need to run the app when you want to start (or reset) a trip. After that the app does not need to be running, until you want to read your trip stats.

Please note that trips in this app differs from the Tesla on-screen trips by that it also counts standby/parked battery usage/losses.


Release: 0.9.6

Jul 21, 10:33 AM

What's new in this release?

  • Multiple trips

  • Storage of trips

  • AC and DC charge counters

Trips work with total counters from the car. This means that the start of a trip is merely a bookmark, you only need to run the app when you want to start (or reset) a trip. After that the app does not need to be running, until you want to read your trip stats. Please note that trips in this app differs from the Tesla on-screen trips by that it also counts standby/parked battery usage/losses.


Release: 0.9.4

Feb 26, 10:56 PM

What's new in this release?

  • Data integrity improvements (fewer crazy values)

  • Unit conversion for imperial units

  • Tidying up the tabs


Release: 0.9.3

Feb 12, 11:03 PM

What's new in this release?

+ CSV files now have a timestamp (milliseconds)


Release: 0.9.2

Feb 8, 10:29 AM

What's new in this release?

+ Another bugfix for CSV on international language phones


Release: 0.91

Feb 7, 8:49 AM

What's new in this release?

+ CSV bugfix on international language phones (comma as decimal point would screw up the CSV logs)



Release: 0.9

Feb 2, 8:53 AM

What's new in this release?

  • Log browser

  • Logs are now written to /sdcard/ScanMyTesla/ (App can only get permission to write logs on Android 5.0. Browsing for logs is acting strange in pre-5.0)


Release: 0.8

Jan 28, 8:18 PM

What's new in this release?

  • Cut & paste

  • Composite values will maintain correct canbus filters

  • CSV logging

  • Raw logging (for dev)

  • Tabs now remember deleted or added/pasted items (but it is not yet stored when app is restarted - coming soon)

  • Trip tab cleanup

  • Added real-time consumption

  • Context menu (long-press an item)

  • Options menu (little down-arrow)

  • Threading bugfixes


Release: 0.7

Jan 11, 11:39 PM

What's new in this release?

  • Fixed negative cell temperatures

  • Added lots of front drive data

  • Improved bluetooth stability


Release: 0.6

Jan 8, 7:54 PM

What's new in this release?

  • Rewritten bluetooth handling

  • Supports ST command set (for OBDLink MX et al)

  • Dynamic filters

  • Long press to delete values


Release: 0.5

Dec 12, 2016, 11:34 PM

What's new in this release?

  • Improved bluetooth adapter compatibility

  • New cell visualisation

  • Various fixes


Release: 0.4

Dec 11, 2016, 2:05 PM

What's new in this release?

  • Tabs

  • Various fixes

  • Accidentally left debug logging enabled


Release: 0.3

Dec 11, 2016, 11:34 AM

What's new in this release?

  • Tabs

  • Various fixes


Release: 0.1

Dec 4, 2016, 9:28 PM

What's new in this release?

  • Now supports more OBD2 devices - app doesn't wait for init string from the adapter upon connection, which some give and some don't.

  • Retries setup commands if no response is given. Will fix lost commands on startup

  • Initialises CAN protocol (auto-detect) on each startup. Fixes 'silent' mode (where the OBD adapter had missed one or more setup commands, and was sending unrecognized formats to the app, leaving the app silent (black screen).


Release: Alpha

Dec 1, 2016, 11:04 AM

What's new in this release?

No release notes.